Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Holmesburg Homeowners
A missing cap is the single most expensive small part on a Holmesburg chimney. One season of rain down an open flue can rust a damper, soften mortar joints, and start the slow water damage that ends in a crown rebuild. The cap and crown are the two pieces doing the most weather work on the whole system, and they’re the two homeowners look at least often. Our technicians have up to 8 years of experience, and they see the same pattern on these rowhouse and twin chimneys: hairline crown cracks that froze and opened wider over winter, then a rusted chase cover beneath a cap that blew off in a nor’easter nobody remembers. We solve that before it reaches the flue.
We book same-day appointments in Holmesburg when the schedule allows, and our team can put a proper cap on, repair a cracked crown, or tell you plainly that yours is fine and can wait. Call (866) 780-1537. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What Our Chimney Cap & Crown Service Includes
Every cap and crown job starts with a look at the whole top of the chimney, not just the part you called about. The cap and crown work as a pair, and fixing one while ignoring the other wastes the money. Here’s what each piece of the service covers.
Cap Installation
A chimney cap is the hooded cover that sits on top of the flue and keeps rain, birds, squirrels, and leaves out of the chimney. You need one if your flue is open to the sky, if you’re hearing scratching or flapping from the chimney, or if water is showing up in the firebox after storms. We install stainless and galvanized caps sized to your actual flue opening, sealed to the crown so water can’t sneak around the edge. We work with Olympia Chimney and Gelco caps, and we match the gauge and mesh to your flue type rather than grabbing whatever’s on hand.

Cap Replacement
Caps fail by rusting through, losing fasteners, or getting bent out of shape by wind and fallen branches. You need a replacement when the cap is loose, corroded, or sitting crooked and letting water past the edge. We pull the old cap, check the crown underneath for damage the failed cap may have caused, and set a new one that fits the flue properly. If the original was the wrong size to begin with, we’ll say so, because a cap that doesn’t seal is barely better than no cap.

Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney that sheds water away from the brick. It cracks as it ages and freezes, and once it does, water gets into the masonry below and starts spalling brick and rusting the damper. You need crown repair when you can see cracks wider than a hairline, crumbling at the edge, or a crown that’s pulling away from the flue. We repair and rebuild crowns with a proper slope so water runs off instead of pooling, and we do it before the damage reaches the flue.

Crown Coating
Crown coating is a flexible, crack-bridging sealant applied over a crown that’s cracked but still structurally sound. You need it when the crown has surface cracks and minor wear but doesn’t need a full rebuild. Coating is the less expensive route, and we’ll tell you honestly when a crown is a candidate and when it isn’t. The point is to stop water at the surface before it gets into the masonry, and a coating only works if the crown underneath is solid enough to hold it.
Multi-Flue Cap
A multi-flue cap is a single cover that spans two or more flues on one chimney, common on Holmesburg homes with a furnace flue and a fireplace flue side by side. You need one when you have multiple flues and want them all protected under a single, cleaner-looking lid. We measure the full footprint, set the cap so each flue still vents properly, and fasten it to the crown so wind can’t lift it. Single-flue caps on a two-flue chimney leave one open, and the open one is the one that takes on water.
Custom Cap
A custom cap is a fabricated cover built to fit a chimney that standard sizes don’t match, whether that’s an odd flue shape, a wide footprint, or an architectural look you want to keep. You need one when off-the-shelf caps don’t seal properly or you want the top of the chimney to match the house. We measure the flue and crown, specify the cap in stainless or copper, and fit it to the actual opening. Custom isn’t about looks alone; a cap that fits the flue precisely is the one that keeps water out for good.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with a set of brands that chimney technicians actually specify, and knowing them matters when a cap or crown job turns into something more. Gelco caps are built for durability and proper venting, and we know where their fasteners and mesh wear over time. Olympia Chimney is a name we reach for on multi-flue and custom covers, and we’ve seen which of their cap styles hold up in the wind and freeze-thaw cycles this part of Philadelphia gets. When a crown repair goes deeper than expected, HeatShield ceramic resurfacing can rebuild a deteriorated flue surface without a full liner tear-out, and DuraFlex flexible liners come into play when the flue itself needs relining alongside the top work.
The reason we name these brands is simple: the right material for the flue type and the job is what protects your chimney, not a one-size cap bolted on because it was handy. A Gelco cap that vents correctly and a crown sealed with the right repair material will outlast a generic cover every time. Whether you have Gelco, Olympia Chimney, or any other make, we can help, and we’ll tell you which parts of your existing setup are worth keeping.
Signs You Need Chimney Cap & Crown Right Now
Some of these you can spot from the ground with binoculars, and some you’ll only know from inside. Here’s what should prompt a call.
- Water in the firebox after rain. If water is pooling in the firebox or staining the damper, the cap is missing, loose, or the crown is cracked and letting water run down the flue. Left alone, that water rusts the damper and softens the mortar.
- A visible crack in the crown. A crack wider than a hairline, or a crown that’s crumbling at the edge, will let water into the masonry below. Freeze-thaw cycles widen those cracks over a single winter, and the repair is far cheaper than the rebuild it leads to.
- Rust streaks on the cap or chase cover. Rust on the cap or the metal cover beneath it means water is sitting where it shouldn’t and the metal is failing. Once it rusts through, the cap stops protecting the flue entirely.
- Animals or debris in the chimney. Scratching, flapping, or nesting material around the flue means the cap or its mesh is open or broken. A chimney open to birds and squirrels is a chimney that clogs and drafts poorly.
- Loose or crooked cap. A cap that shifts in the wind or sits off-angle isn’t sealing, and it can come off entirely in a storm. That’s a cap replacement job, and it’s worth doing before the next blow.
Our Chimney Cap & Crown Process – Step by Step
- 1
We start with an inspection of the whole top. Before we quote a cap or crown, we look at the flue, the crown, the brick below it, and the chase cover, because a cap on a failing crown doesn’t fix anything. We use a camera to check the flue interior so you see what we see, and we tell you plainly if something can safely wait.
- 2
We give you a written estimate with the price set per job. The estimate lays out what needs doing, which material we’re specifying, and what it costs, before any work begins. No surprise numbers, and no pressure to do the crown if a cap is all you need.
- 3
We repair or rebuild the crown first when it’s needed. A cracked crown gets repaired or rebuilt with a proper slope so water sheds away from the flue, and a sound crown is what a good cap seals against. If the crown is only lightly worn, we may recommend crown coating instead of a rebuild.
- 4
We fit the right cap for your flue. Single-flue, multi-flue, or custom, we size the cap to your actual opening and the flue type, then fasten it to the crown so it seals and stays put. The cap is the top of the system, and we treat it that way.
- 5
We check the whole system before we leave. That means the cap is seated, the crown sheds water, and the flue is clear and venting properly. You get a photo report of what we found and what we changed, so you can see the work for yourself.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Holmesburg?
A typical chimney cap installation in Holmesburg runs roughly $200 to $450 depending on the flue size and the material, with custom and multi-flue caps at the higher end. A crown repair or rebuild typically runs $300 to $900, and crown coating sits lower because it treats the surface rather than rebuilding it. The range is wide because a crown job on a single-flue rowhouse chimney is a very different scope from a rebuild on a wide twin.
What drives the number: how many flues you have, whether the crown needs a full rebuild or just coating, the cap material (stainless lasts longer than galvanized), and whether the crown is so far gone that the brick below it needs attention too. The way to avoid overpaying is to get the written estimate that breaks the work out line by line, so you know what you’re paying for. We work with HeatShield and DuraFlex where a full rebuild isn’t necessary, which can save real money when the problem is under the crown rather than in the crown.
Your free estimate includes the inspection, the camera look down the flue, and the photo report. Nothing is recommended without evidence you can see, and we’ll tell you outright when a job can safely wait. The written estimate sets the final price, and it’s per job, so what you’re quoted is what you pay. Call (866) 780-1537 for an exact quote; estimates are free.
Chimney Cap & Crown Near Holmesburg – Our Service Area
We cover Holmesburg and the neighborhoods around it, including Mayfair, Rhawnhurst, Tacony, Torresdale, Oxford Circle, Fox Chase, Bustleton, and Frankford, along with Eddington and Bryn Athyn just over the line. Most of these are a short drive from our dispatch, and a booked job is usually reachable same-day when the schedule allows. Homeowners in these communities often ask us about chimney cap & crown work for the same rowhouse and twin chimneys we see in Holmesburg. If you’re further out in Northeast Philadelphia, call and we’ll talk through the timing.
Serving Holmesburg, PA – Our Local Coverage Area
We serve Holmesburg and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Holmesburg
Chimney cap and crown service means installing or replacing the cap on top of the flue and repairing, coating, or rebuilding the concrete crown that sheds water off the chimney. The cap keeps rain, animals, and debris out of the flue, and the crown keeps water out of the masonry. Together they’re the first line of defense for the entire chimney system, which is why we treat them as one job rather than two.
Most cap installations and crown coating take a couple of hours, while a full crown rebuild or a custom cap can take longer and sometimes needs a return visit. The schedule depends on how much prep the crown needs and whether we’re working around weather. We’ll give you a realistic window with the written estimate, and we book the job so you’re not left guessing. Call (866) 780-1537 to talk through your timing.
Cap installation typically runs about $200 to $450, crown repair or rebuild runs roughly $300 to $900, and crown coating costs less because it treats the existing surface. The final price depends on flue count, material, and how much of the crown needs rebuilding. Your free estimate breaks it out line by line, and the written estimate sets the final price. Call (866) 780-1537 for an exact quote; estimates are free.
Yes, we service Olympia Chimney and Gelco caps and can fit replacements from those brands when the existing cap has failed. We also work with DuraFlex and HeatShield when the flue itself needs attention under the cap. Knowing these brands means we can match the right cap and repair material to your flue type rather than guessing. Whether you have Olympia Chimney, Gelco, or another make, we can help.
We book same-day appointments when the schedule allows, and our team can often assess a cap or crown the same day you call. We answer 24/7 on the phone line, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday, and a call outside dispatch hours is booked into the next opening. Call (866) 780-1537 and we’ll find the earliest slot for you.
Yes, our cap and crown work is covered by a satisfaction guarantee, and the written estimate spells out exactly what’s covered. We stand behind the materials and the installation, and we’ll come back if something isn’t right. Ask about coverage for your specific job when you call, since it depends on the material and scope. The local pro is licensed and insured as their state requires.
There’s not much you need to do beyond clear access to the chimney and letting us know if you have a fireplace or wood stove in use. If you have photos of the cap or crown from the ground, they help us plan before we arrive. We handle the rest, including the camera inspection and the photo report. Call (866) 780-1537 if you have questions before the visit.
Schedule Your Chimney Cap & Crown Service in Holmesburg Today
A cap and crown in good shape protect everything below them, and our team can tell you in one visit whether yours is doing its job. Call (866) 780-1537. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Your free estimate includes the inspection, the camera look, and a photo report, with a no-obligation price and the written estimate setting the final number. We’ll tell you when work can safely wait, and when it can’t.
Written by the team at Chimney Sweep Holmesburg.